'68 327 Sbc For Sale

[OVRBST]

I have a 1968 327 for sale.
.030 over
JE pistons/molly rings
Chevy Pink rods
Forged Crank (stock)
lightly ported 62 vette 1.94 heads (re-freshed with new valves, springs, guides, and seals) P.S. 1962 means no threaded accesory holes on the heads :(
Crane Cams Fireball2 (cant remember duration, but its got 480lift)
Crane Roller rockers (1.6)
New bearings, seals, gaskets
Weiand Intake mani
Holley650 DP carb. (Most likely needs re-build)
Edelbrock Elite aircleaner and valve covers
I think I have the starter, distributor, cap and rotor. I'll have to check to make sure. No wires, and I'll even give you the used Accell Plugs :)

Engine has a total of maybe 2K miles on it. The Iroc it was in got rear-ended by a paving truck, and totaled shortly after I put the motor in. Ran pretty good, but the shorty headers, T intersecting midpipe, and 3" single exhaust just didn't agree with it. I'm sure this motor can make some nice power with a set of aluminum 2.02 heads and better exhaust.

Make me an offer!!!! a reasonable one please. I have receipts for EVERY LAST LITTLE THING in the motor, including the machine work.
Pick ups only, unless you wanna pay me to bring it to you.

EDIT::: I'll try to snap some pics when I get a chance if anyone is interested.

[igotasweetride]

Originally posted by OVRBST
I have a 1968 327 for sale.
.030 over
JE pistons/molly rings
Chevy Pink rods
Forged Crank (stock)
lightly ported 62 vette 1.94 heads (re-freshed with new valves, springs, guides, and seals) P.S. 1962 means no threaded accesory holes on the heads :(
Crane Cams Fireball2 (cant remember duration, but its got 480lift)
Crane Roller rockers (1.6)
New bearings, seals, gaskets
Weiand Intake mani
Holley650 DP carb. (Most likely needs re-build)
Edelbrock Elite aircleaner and valve covers
I think I have the starter, distributor, cap and rotor. I'll have to check to make sure. No wires, and I'll even give you the used Accell Plugs :)

Engine has a total of maybe 2K miles on it. The Iroc it was in got rear-ended by a paving truck, and totaled shortly after I put the motor in. Ran pretty good, but the shorty headers, T intersecting midpipe, and 3" single exhaust just didn't agree with it. I'm sure this motor can make some nice power with a set of aluminum 2.02 heads and better exhaust.

Make me an offer!!!! a reasonable one please. I have receipts for EVERY LAST LITTLE THING in the motor, including the machine work.
Pick ups only, unless you wanna pay me to bring it to you.

EDIT::: I'll try to snap some pics when I get a chance if anyone is interested.

any idea on the compression ratio and how much power its putting out.

[OVRBST]

Ohh ya, sorry. Compression is 11.5:1.

On paper with the heads it has right now I think it said around 350HP. With a nicer set of heads it should make somwhere near 400HP.

Ohhh it also has a fluiddamper balancer :)

[igotasweetride]

im not interested, just askin the shit everyone else will to save you the time later. toss out a number you want for it, theres gotta be a mullet head on here lookin for a motor.

[OVRBST]

Well thanks for reminding me. It's been a while since I've talked domestic :)


I just need to make some room. I have over 3K invested in this little mouse motor.

If I get 1/3 of that money back I'll be happy.

So for the math-uhh-maticians....that's $1000. :)....or best offer.

[igotasweetride]

Originally posted by OVRBST
Well thanks for reminding me. It's been a while since I've talked domestic :)


I just need to make some room. I have over 3K invested in this little mouse motor.

If I get 1/3 of that money back I'll be happy.

So for the math-uhh-maticians....that's $1000. :)....or best offer.

ill give ya 1200 for it if you toss in the supra with it :thumbsup:

[OVRBST]

ill give ya 1200 for it if you toss in the supra with it

damn that's almost to good to pass up....BUT...

[igotasweetride]

Originally posted by OVRBST
damn that's almost to good to pass up....BUT...


lol, DAMN. i figured id try. ill toss in a 94 talon TSi, near mint body, mint interior, runs mint too. all yours. shit, ill even toss in some stock parts off my truck :lol:








ok, im done highjackin your thread with useless shit

[OVRBST]

C'mon fellas. I'm sure SOMEONE needs a nice small block?

[igotasweetride]

Originally posted by OVRBST
C'mon fellas. I'm sure SOMEONE needs a nice small block?

i do now as i just picked up a maro, the only problem is im broke.

[540Malibu]

has the block been decked? if not what are the suffix codes, and whats the casting number on the back of the block.

[OVRBST]

The block was decked. I cannot remember how much, but it was just enough to make some of the numbers dissapear off the front deck. The casting numbers on the back are 3914678.

I just snapped some pictures, and should have those up shortly.

EDIT::: Ok here are some pictures. The intake mani is an old style Weiand, that's why it still had the option for adding a front oil filler. It is kinda dirty. Didn't bother cleaning it to much after it came out of the car.
http://www.hudsonimports.com/327back.jpg
http://www.hudsonimports.com/327front.jpg
http://www.hudsonimports.com/327front1.jpg